1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
|
0. Intro.
Onion Routing is still very much in development stages. This document
aims to get you started in the right direction if you want to understand
the code, add features, fix bugs, etc.
Read the README file first, so you can get familiar with the basics.
1. The pieces.
1.1. Routers. Onion routers, as far as the 'or' program is concerned,
are a bunch of data items that are loaded into the router_array when
the program starts. After it's loaded, the router information is never
changed. When a new OR connection is started (see below), the relevant
information is copied from the router struct to the connection struct.
1.2. Connections. A connection is a long-standing tcp socket between
nodes. A connection is named based on what it's connected to -- an "OR
connection" has an onion router on the other end, an "OP connection" has
an onion proxy on the other end, an "exit connection" has a website or
other server on the other end, and an "AP connection" has an application
proxy (and thus a user) on the other end.
1.3. Circuits. A circuit is a single conversation between two
participants over the onion routing network. One end of the circuit has
an AP connection, and the other end has an exit connection. AP and exit
connections have only one circuit associated with them (and thus these
connection types are closed when the circuit is closed), whereas OP and
OR connections multiplex many circuits at once, and stay standing even
when there are no circuits running over them.
1.4. Cells. Some connections, specifically OR and OP connections, speak
"cells". This means that data over that connection is bundled into 128
byte packets (8 bytes of header and 120 bytes of payload). Each cell has
a type, or "command", which indicates what it's for.
2. Important parameters in the code.
2.1. Role.
3. Robustness features.
3.1. Bandwidth throttling. Each cell-speaking connection has a maximum
bandwidth it can use, as specified in the routers.or file. Bandwidth
throttling occurs on both the sender side and the receiving side. The
sending side sends cells at regularly spaced intervals (e.g., a connection
with a bandwidth of 12800B/s would queue a cell every 10ms). The receiving
side protects against misbehaving servers that send cells more frequently,
by using a simple token bucket:
Each connection has a token bucket with a specified capacity. Tokens are
added to the bucket each second (when the bucket is full, new tokens
are discarded.) Each token represents permission to receive one byte
from the network --- to receive a byte, the connection must remove a
token from the bucket. Thus if the bucket is empty, that connection must
wait until more tokens arrive. The number of tokens we add enforces a
longterm average rate of incoming bytes, yet we still permit short-term
bursts above the allowed bandwidth. Currently bucket sizes are set to
ten seconds worth of traffic.
The bandwidth throttling uses TCP to push back when we stop reading.
We extend it with token buckets to allow more flexibility for traffic
bursts.
3.2. Data congestion control. Even with the above bandwidth throttling,
we still need to worry about congestion, either accidental or intentional.
If a lot of people make circuits into same node, and they all come out
through the same connection, then that connection may become saturated
(be unable to send out data cells as quickly as it wants to). An adversary
can make a 'put' request through the onion routing network to a webserver
he owns, and then refuse to read any of the bytes at the webserver end
of the circuit. These bottlenecks can propagate back through the entire
network, mucking up everything.
To handle this congestion, each circuit starts out with a receive
window at each node of 100 cells -- it is willing to receive at most 100
cells on that circuit. (It handles each direction separately; so that's
really 100 cells forward and 100 cells back.) The edge of the circuit
is willing to create at most 100 cells from data coming from outside the
onion routing network. Nodes in the middle of the circuit will tear down
the circuit if a data cell arrives when the receive window is 0. When
data has traversed the network, the edge node buffers it on its outbuf,
and evaluates whether to respond with a 'sendme' acknowledgement: if its
outbuf is not too full, and its receive window is less than 90, then it
queues a 'sendme' cell backwards in the circuit. Each node that receives
the sendme increments its window by 10 and passes the cell onward.
In practice, all the nodes in the circuit maintain a receive window
close to 100 except the exit node, which stays around 0, periodically
receiving a sendme and reading 10 more data cells from the webserver.
In this way we can use pretty much all of the available bandwidth for
data, but gracefully back off when faced with multiple circuits (a new
sendme arrives only after some cells have traversed the entire network),
stalled network connections, or attacks.
We don't need to reimplement full tcp windows, with sequence numbers,
the ability to drop cells when we're full etc, because the tcp streams
already guarantee in-order delivery of each cell. Rather than trying
to build some sort of tcp-on-tcp scheme, we implement this minimal data
congestion control; so far it's enough.
3.3. Router twins. In many cases when we ask for a router with a given
address and port, we really mean a router who knows a given key. Router
twins are two or more routers that all share the same private key. We thus
give routers extra flexibility in choosing the next hop in the circuit: if
some of the twins are down or slow, it can choose the more available ones.
Currently the code tries for the primary router first, and if it's down,
chooses the first available twin.
|